Zero-water cryogenic mold removal for homes and businesses

Dry ice blasting mold SOUTH EL MONTE CA done right the first time

When mold shows up in your South El Monte home or shop, dry ice blasting mold SOUTH EL MONTE CA is the fastest way to kill it without soaking your framing, drywall, or insulation. Our crew uses cryogenic mold removal SOUTH EL MONTE California to freeze spores off wood, concrete, and metal in a single pass. We serve Los Angeles County homeowners, landlords, and property managers who need the job done clean, fast, and code-correct.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dry Ice Blasting Mold by Mold Remediation Service South El Monte
Careful work. Honest options.
About this service

What dry ice blasting mold SOUTH EL MONTE CA actually does

Dry ice blasting mold SOUTH EL MONTE CA is a cryogenic cleaning method that fires compressed pellets of frozen CO2 at minus 109 degrees Fahrenheit onto mold-contaminated surfaces. The pellets hit the mold, flash-freeze it, and lift it off the substrate without water, sand, or chemical residue. Because the dry ice sublimates on contact, there is nothing to vacuum up but the mold itself. We pair the blaster with HEPA vacuuming and a boroscope inspection camera so nothing gets missed inside wall cavities.

South El Monte sits in a basin where summer humidity climbs and winter rain finds every crack in older stucco and flat roofs. That combination feeds black mold growth behind drywall, under crawl space moisture barriers, and inside HVAC plenums. If you have been searching for dry ice mold removal near me SOUTH EL MONTE California, you are likely dealing with a leak that has been feeding spores for weeks. We stop the moisture source first, then blast the growth.

  • ✓ No water, no secondary damage
  • ✓ Reaches tight framing cavities
  • ✓ Kills spores, not your schedule
  • ✓ Safe on wood, metal, and concrete
What's included

What our dry ice blasting mold service includes

Every dry ice blasting mold SOUTH EL MONTE CA job comes with the same core scope: inspection, containment, blasting, HEPA vacuuming, antimicrobial treatment, and clearance testing. If your job needs drywall removal or a moisture barrier install, we quote that separately before we start.

✓

Moisture mapping and inspection

We use a moisture meter and thermal imaging camera to find every wet area feeding the mold. A boroscope inspection camera checks inside wall cavities. This step takes 45 to 90 minutes and determines the blast scope.

✓

Containment and air scrubbing

Plastic sheeting seals the work zone. A Dri-Eaz air scrubber with HEPA filters runs the entire time to keep spores from spreading. Technicians wear Tyvek suits and respirators per OSHA compliance.

✓

Dry ice blasting of affected surfaces

We blast framing, sheathing, concrete, and metal at 90 to 150 PSI. The dry ice sublimates on contact, so there is no water and no media cleanup. Most residential surfaces are done in a single pass.

✓

HEPA vacuum and antimicrobial coating

After blasting, we HEPA vacuum every surface and apply a mold remediation chemical such as Concrobium or Benefect. Framing gets an antimicrobial coating to stop regrowth if humidity climbs again.

✓

Post-remediation clearance testing

A spore trap sampler collects air samples that go to EMSL Analytical or ProLab. If counts are at or below outdoor baseline, you get a written clearance report. If not, we re-blast at no extra charge.

How it works

Our dry ice blasting mold removal process

01

Inspection and testing

We start with a moisture meter and thermal imaging camera to map where water is hiding. Air samples go to EMSL Analytical or ProLab for spore counts, and we use a mold test kit on suspect surfaces. This step takes 45 to 90 minutes and tells us whether you have a localized problem or an HVAC mold contamination issue.

02

Containment setup

We seal the work zone with plastic sheeting and run a Dri-Eaz air scrubber with HEPA filters to keep spores from drifting into the rest of your home. Technicians suit up in Tyvek suits and respirators. Setup runs about 30 minutes on a typical bedroom or attic job.

03

Dry ice blasting

Our technician runs the dry ice blasting machine at 90 to 150 PSI depending on the substrate. Pellets freeze the mold and lift it off in one pass. A 300-square-foot attic takes two to three hours. We work section by section and check each area with a boroscope inspection camera before moving on.

04

HEPA vacuum and treatment

Once the mold is off, we HEPA vacuum every surface and apply a mold remediation chemical such as Concrobium or Benefect to the cleaned area. On framing, we finish with an antimicrobial coating. This step locks in the result and stops regrowth if humidity spikes again.

05

Post-remediation verification

We run a final spore trap sampler and compare the numbers to our baseline. If clearance passes, we hand you the lab report and a written scope of what was cleaned. If it does not, we re-blast at no extra charge. Most jobs clear on the first pass.

Tools & methods

Tools and methods we use on every job

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Dry ice blasting machine

Fires CO2 pellets at 90 to 150 PSI to freeze and lift mold off framing, concrete, and metal without water or abrasive media.

Thermal imaging camera

Finds hidden moisture behind walls and under floors by reading temperature differences. Used during inspection to map the full extent of the problem.

Boroscope inspection camera

Slides into wall cavities and ductwork to confirm mold growth in areas we cannot see. Verifies the blast reached every contaminated surface.

Dri-Eaz air scrubber with HEPA filters

Runs during containment to filter airborne spores and keep them from spreading into clean areas of the property.

HEPA vacuum

Removes settled spores and debris after blasting. Captures particles down to 0.3 microns so nothing is left behind on the surface.

Spore trap sampler

Collects air samples before and after remediation. Samples go to EMSL Analytical or ProLab for lab analysis and clearance documentation.

Fogging machine

Applies a fine mist of mold remediation chemical into ductwork and crevices that blasting cannot reach directly.

Real results

Before and after.

Attic sheathing after a roof leak

Before

A 300-square-foot attic in the Durfee Avenue Area had black mold growth across the roof sheathing and rafters from a slow leak that had been running for months. Insulation was damp and the musty smell was pulling into the bedrooms.

After

We contained the attic, blasted the sheathing and rafters in three hours, HEPA vacuumed, and replaced the insulation. Post-remediation testing came back at outdoor baseline. The homeowner had a clearance report for the insurance claim.

Crawl space joists with moisture damage

Before

A home near Merced Avenue had mold on the floor joists and subfloor from years of crawl space moisture. The moisture barrier was torn and standing water had been sitting after winter rains.

After

We replaced the moisture barrier, blasted the joists and subfloor with dry ice, and applied an antimicrobial coating. A dehumidifier was installed. Spore counts dropped from 4,200 to 380 spores per cubic meter.

Commercial warehouse racking after a leak

Before

A warehouse unit in the South El Monte Industrial Park had mold on steel racking and concrete walls after a roof leak. The tenant needed the space back in service within 48 hours.

After

We ran industrial dry ice blasting mold SOUTH EL MONTE equipment overnight. Racking and concrete were cleaned in six hours, fogging covered the remaining crevices, and clearance testing passed the next morning. The tenant moved back in that afternoon.

Problems we solve

Mold problems we solve with dry ice blasting

Most South El Monte mold calls come down to one of four problems: a hidden leak, a damp crawl space, an attic that never dries out, or an HVAC system spreading spores through the whole building. Dry ice blasting handles all four without tearing your property apart.

Ask a pro →
01

Black mold growth behind drywall after a slow leak

We cut a small access panel, confirm growth with a boroscope inspection camera, and blast the framing clean with dry ice. The cavity gets HEPA vacuumed and coated, then we close it up. Most wall cavities are done in under two hours.

↗
02

Crawl space moisture feeding mold on joists and subfloor

We install or repair the moisture barrier, then blast the joists and subfloor with dry ice. No water is added to a space that already struggles to dry. We finish with an antimicrobial coating and a dehumidifier recommendation.

↗
03

Attic condensation and roof leak mold on sheathing

We contain the attic, blast the sheathing and rafters, HEPA vacuum the space, and replace any ruined insulation. A 300-square-foot attic typically takes two to three hours of blasting and clears on the first lab test.

↗
04

HVAC mold contamination spreading spores room to room

We isolate the HVAC system, blast the coils and plenum with dry ice, and fog the ductwork with a mold remediation chemical. Post-remediation testing confirms the air is clean before we turn the system back on.

↗
Proof you can check

Licensed, certified, and verified

✓
IICRC CertificationInstitute of Inspection, Cleaning and Restoration Certification
✓
ACAC CertificationAmerican Council for Accredited Certification
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
✓
California State Contractor LicenseCalifornia Contractors State License Board
✓
Indoor Air Quality Association CertificationIndoor Air Quality Association
Good questions

Frequently asked questions about dry ice blasting mold

(833) 929-5837 →

Most residential jobs run $650 to $1,800, and commercial work starts around $2,200. Price depends on square footage, how deep the mold has grown into the substrate, and whether we need to open walls. A single attic or crawl space is usually on the low end. We give you a flat quote before we start, and that number does not change unless you add scope.

Yes. Dry ice blasting is safe for wood, metal, concrete, brick, and most electrical components when done by a trained technician. There is no water, so no secondary moisture damage. The CO2 sublimates into the air and vents out. We still run containment and HEPA filtration because the mold spores themselves are the hazard, not the blasting media. Every technician wears a respirator and Tyvek suit.

We clean framing lumber, plywood sheathing, concrete block, brick, steel studs, HVAC coils and plenums, subfloor, joists, and even some antique wood. It is not ideal for soft materials like insulation or already-crumbling drywall, which we remove and replace instead. If you are unsure about a surface, send us a photo and we will tell you straight.

It is the best method we have for framing. The pellets get into the grain and lift mold off without sanding away the wood. We follow with a HEPA vacuum and an antimicrobial coating. On a typical 2x4 stud bay, we can clean 10 to 12 linear feet in about 15 minutes. Post-remediation testing confirms the framing is clear before we close anything up.

Ready when you are

Get dry ice blasting mold SOUTH EL MONTE CA scheduled today

We are licensed, insured, and carry IICRC certification on every crew. Call (833) 929-5837 and we will inspect, quote a flat rate, and schedule your dry ice blasting mold removal SOUTH EL MONTE California job, often the same day.

Call Now (833) 929-5837 →
Request an appointment

Contact our SOUTH EL MONTE mold team

Call (833) 929-5837 any time, day or night. We answer live for emergencies and schedule free walkthroughs during normal business hours. If you'd rather send details, email us photos of what you're seeing and we'll get back to you with next steps.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837